RB12 Relay Board
Product code: IC-RB12
Provides 12 industry standard relay module sockets to a U3, U6, UE9, T4, or T7. Commonly used to interface a LabJack with high voltages/currents. The RB12 relay board connects to the DB15 connector on the LabJack, using the 12 EIO/CIO lines to control up to 12 I/O modules.
$336.00
AUD + GST
$369.60
AUD Inc. GST
PS12DC Power Switching Board
Product code: IC-PS12DC
Controlled through 12 digital outputs, the PS12DC can switch power sources ranging from 5 to 28V DC. Attach the PS12DC to the DB15 connector presented on all compatible devices, and toggle the states of the EIO and CIO digital output lines to turn the switches on/off.
$219.00
AUD + GST
$240.90
AUD Inc. GST
Mux80 AIN Expansion Board
Product code: IC-Mux80
Analog input expansion board that adds 80 analog input channels. It can be connected to a U6, UE9, or T7 directly through the DB37 connector.
$339.00
AUD + GST
$372.90
AUD Inc. GST
LM34CAZ Silicon Temperature Sensor
Product code: IC-LM34CAZ
The LM34CAZ is ideal for cold-junction compensation(CJC) temperature measurements. Customers who are using thermocouples on an external CB37 terminal board can wire this sensor to a nearby analog input, and correlate the CJC offset within software.
$25.00
AUD + GST
$27.50
AUD Inc. GST
LJTick RelayDriver
Product code: IC-LJTick-RelayDriver
Allows 2 digital I/O lines to each control a relay or other moderate load. The 4-pin design plugs into the standard DIO/DIO/GND/VS screw terminal block found on LabJacks such as the U3, U6, UE9, T7, and T4. Each DIO controls a switch to ground (i.e. open-collector) that can hold off up to 50 volts and can sink up to 200 mA.
$35.00
AUD + GST
$38.50
AUD Inc. GST
LJTick Proto
Product code: IC-LJTick-Proto
The LJTick-Proto (LJTP) consists of an 8x8 grid of holes for prototyping custom signal-conditioning ticks. The 4-pin design plugs into the standard AIN/AIN/GND/VS screw terminal block found on LabJacks such as the U3, U6, UE9, T7, and T4. Includes 3 loose pieces: the PCB, a 4-position screw terminal, and a right-angle pin header.
$20.00
AUD + GST
$22.00
AUD Inc. GST
LJTick OutBuff
Product code: IC-LJTick-OutBuff
Increases the output current of the DAC outputs on LabJack devices. Can also be used for switched 3.3V when attached to a 3.3V digital I/O line. LabJack devices cannot output more than about 15mA on their DAC0 and DAC1 analog outputs, so this accessory is very helpful for users who want to increase that capability. One common application is to control the speed of a low voltage DC motor.
$45.00
AUD + GST
$49.50
AUD Inc. GST
LJTick LVDigitalIO
Product code: IC-LJTick-LVDigitalIO
A bidirectional logic shifting board for converting 3.3V logic down to 2.5V or 1.8V. There is also a VOUT terminal which can source power at the selected voltage. Useful for users who have external boards that run on lower logic thresholds, or simply want a 3.3V, 2.5V, or 1.8V supply.
$45.00
AUD + GST
$49.50
AUD Inc. GST
LJTick InBuff
Product code: IC-LJTick-InBuff
Very low bias current (1pA) input buffer which can directly measure pH sensors (electrode type sensors) and other weakly driven or high source impedance signals. The analog inputs on our compatible DAQ products (U3, U6, UE9, T7, T4) have typical bias currents on the order of 20 nA, which is quite low, but the LJTick-InBuff reduces that dramatically.
$89.00
AUD + GST
$97.90
AUD Inc. GST
LJTick InAmp
Product code: IC-LJTick-InAmp
Signal-conditioning module provides two instrumentation amplifiers ideal for low-level signals such as bridge circuits (e.g. strain gauges) and thermocouples. Each amplifier converts a differential input to single-ended.
$169.00
AUD + GST
$185.90
AUD Inc. GST
LJTick DigitalOut5V
Product code: IC-LJTick-DigitalOut5V
Converts 3.3V digital outputs to 5V digital outputs. Easily control 5V relays, or interface with a 5V logic device.
$49.00
AUD + GST
$53.90
AUD Inc. GST
LJTick DAC
Product code: IC-LJTick-DAC
Provides a pair of 14-bit analog outputs with a range of +/- 10 volts. Plugs into any digital I/O block (e.g. FIO4/FIO5), and thus up to 10 of these can be used per LabJack to add 20 analog outputs. Works with T-Series devices (T7, T4) and any UD family device (U3/U6/UE9).
$179.00
AUD + GST
$196.90
AUD Inc. GST
LJTick CurrentShunt
Product code: IC-LJTick-CurrentShunt
The LJTick-CurrentShunt (LJTCS) is a signal-conditioning module designed to convert a 4-20 mA current loop input signal into a 0.47-2.36 volt signal compatible with the LabJack U3, U6, UE9, T7, or T4. The 4-pin design plugs into the standard AIN/AIN/GND/VS screw terminal block found on LabJacks such as the U3, U6, UE9, T7, and T4.
$120.00
AUD + GST
$132.00
AUD Inc. GST
$11.00
AUD + GST
$12.10
AUD Inc. GST
$36.50
AUD + GST
$40.15
AUD Inc. GST
$11.00
AUD + GST
$12.10
AUD Inc. GST
Graphtec GL840 Case - IC-GL-840-CASE
Product code: IC-GL-840-CASE
Graphtec GL840 Carry Case, plastic with foam insert.
$200.00
AUD + GST
$220.00
AUD Inc. GST
Graphtec B-569 Rechargeable Lithium-ion battery pack - IC-B-569
Product code: IC-B-569
Graphtec Lithium-ion Battery.
$295.00
AUD + GST
$324.50
AUD Inc. GST
CB37 Terminal Board
Product code: IC-CB37
Provides convenient screw terminals for the DB37 connector on the LabJack U6, UE9, and T7. Includes a screwdriver. Compatible with LJTick signal-conditioning modules.
$154.81
AUD + GST
$170.29
AUD Inc. GST
CB25 Terminal Board
Product code: IC-CB25
Provides screw terminal connections for the LabJack U12's 16 extra digital I/O. A screwdriver and DB25 cable are included. For the LabJack U12 only.
$89.00
AUD + GST
$97.90
AUD Inc. GST
CB15 Terminal Board
Product code: IC-CB15
Provides convenient screw terminals for the 12 digital I/O lines on the DB15 connector of compatible LabJack devices. Includes a screwdriver. Not compatible with the U12.
$95.09
AUD + GST
$104.60
AUD Inc. GST
B-513 Logic Input/Output cable, 2 metres in length, bare wire end - IC-B-513
Product code: IC-B-513
B-513 Logic Input/Output cable, 2 metres in length, bare wire end.
$175.00
AUD + GST
$192.50
AUD Inc. GST
EB37 Experiment Board
Product code: IC-EB37
Just like any breadboard, the EB37 is very useful for testing and validating electronic designs, but it also has a few different power supply rail voltages and breaks out LabJack I/O right next to your design.